Offices in Montana, Florida, California, Texas and Minnesota
Kuefler on twitter Kuefler on facebook

Series 800 – Lightning Protection Conductor Fasteners

Conductor fasteners are used to fasten down the conductor at intervals not to exceed 36” on center. These lightning protection products are made to be glued, nailed or screwed into or onto the surface of the roof for rooftop conductor supports and downlead cable supports. There are special types of cable supports depending on the surface that you are applying them too; i.e., standing seam roofs, rubber membrane roofs or typical shingled roofs. All of the lightning protection conductor fasteners also require nails, screws, drive in anchors, adhesive or bolts to fasten the conductor down.

To place an order please call or fill out this Quote Form.

Copper and Aluminum Cable Straps, One and Two hole


cable straps one hole and two hole series 803, 804, 805, 806


Cable Strap - Copper, One Hole
LPC803 1/2" secured with nails or screws
LPC805 5/8" secured with screws or 1/4" fasteners
Cable Strap - Aluminum, One Hole
LPA803 1/2" secured with nails or screws
LPA805 5/8" secured with screws or 1/4" fasteners
Cable Strap - Copper, Two Hole
LPC804 1/2" secured with nails or screws
LPC806 5/8" secured with screws or 1/4" fasteners
Cable Strap - Aluminum, Two Hole
LPA804 1/2" secured with nails or screws
LPA806 5/8" secured with screws or 1/4" fasteners


Lightning Protection Cable Holders

Flat cable holder for use with hot pitch, roofing compound or commercial adhesive on built-up roof surfaces or other location where holes cannot be made for anchoring cable. Click here for Crimp Bonding Plate


cable holders series 809 & 810

Series 809
LPC809 for copper cables
LPA809 for aluminum cables
Series 810
LPC810 for copper cables
LPA810 for aluminum cables


Lightning Protection Standing-Seam - No Penetration

Brass or aluminum cable holder for standing seam roofing systems. Bottom groove machined 1/2" wide and 3/4" deep to secure on seam with set screw. Cable fastener adjusts for either parallel or perpendicular cable runs. For use with LP801, 803, 805, and 807.

Standing-seam - no penetration series 814

Series 814
LPC814 for copper cable saddle
LPA814 for aluminum cable saddle


Lightning Protection Standing-Seam - No Penetration

Stainless steel cable holder for standing seam roofing systems. Groove is variangle up to 1" wide for rectangular seams or beams, also suitable mounting to seams with rounded or oxed ridge up to 1-1/2" wide. Cable fastener adjusts for either parallel or perpendicular cable runds. For use with LP801, 803, 805, 807 or air terminal bases.

OTHER STANDING SEAM FASTENERS ARE AVAILABLE UPON REQUEST DUE TO THE NUMEROURS STYLES OF STANDING SEAM ROOFS (i.e, width, style, height and etc.).

standing seam series 815

Series 815
LPS815 for all cables


standing seam roof protection
Standing Seam Roof Protection

(click image for larger view)

Tree Lightning Cable Spike Anchor

Tree lightning cable spike anchor

R151
Heavy duty bronze cast tree drive anchor for main or miniature cable. Allows for growth of tree and wind sway. Should be used on mature trees with 1” or thicker bark. Drive anchor then pinch cable holder.
Tek Screw
Tek Screw

Drive-In Anchor
Drive-in anchor


A927P923 410 magnetic stainless steel hex pan-head self-drilling tek screw #10 x 3/4"

A927P924 410 magnetic stainless steel hex pan-head self-drilling tek screw #10 x 1"


A930W004 one-piece lead drive-In anchor with stainless steel nail, 1/4" x 1-1/4"


Standing Seam Clip

Cable holder for standing seam has a 3/4” groove to fit over most seams. Cable holder is adjustable so cables can run perpendicular or parallel. Single set screw holds clip to seam. Loop and cable anchored to clip using a 1/4” bolt. UL Listed

standing Seam Clip

Clip with 1/4" bolt
A714 Aluminum
C714 Bronze
C714L Lead Coated Bronze


Stainless Steel Nail


Stainless Steel Nail

S722 – 6d Stainless Steel ring shank nail – 2" length


Tek Screw with Neoprene Washer


Tek Screw with Neoprene Washer

S725W - #10 x 1” Self drilling screw with neoprene washer
S727W - #10 x 1-1/2” Self drilling screw with neoprene washer
S728W - #10 x 2” Self drilling screw with neoprene washer


Stainless Steel Bolts


Stainless Steel Bolt

HEX HEAD BOLTS-FULL THREADS
STAINLESS STEEL BOLTS
SHB725 #10 X 1”
S730 - 1/4” x 1/2” S737 5/16” x 1”
S731 - 1/4” x 3/4” S738 5/16” x 1-1/4”
S732 - 1/4” x 1” S739 5/16” x 1-1/2”
S733 - 1/4” x 1-1/4” S740 5/16” x 2”
S734 - 1/4” x 1-1/2” S741X58 3/8” x 5/8”
S734x2 - 1/4” x 2” S741 3/8” x 3/4”
S734x225 - 1/4” x 2-1/4” S742 3/8” x 1”
S735 - 5/16” x 3/4” S743 3/8” x 1-1/4”
S736 - 5/16” x 7/8” S745 3/8” x 2”
S747 - 1/2” x 3/4”
S749X2 - 1/2" x 2”


Stainless Steel and Bronze Flat Washers


Stainless Steel and Bronze Flat Washers

FLAT WASHER
Stainless Steel
S750 - 1/4”
S751 - 5/16”
S752 - 3/8”
S753 - 1/2”
S754 - 5/8”
S754X34 - 3/4”
Brass
C754 - 5/8”


Stainless Steel and Brass Lock Washers


Series 800 LOck Washer
LOCK WASHER
Stainless Steel
S755 - 1/4”
S756 - 5/16”
S757 - 3/8”
S758 - 1/2"
S759 - 5/8”
S759X34 - 3/4”

External Tooth Lock Washer
EXTERNAL TOOTH LOCK WASHER
S756XT - 5/16” external tooth lock washer
S758XT - 1/2” external tooth lock washer
Brass
C759XT - 5/8” external tooth lock washer


Neoprene Washers

Neoprene Washers
P760 - #10
P761 - 1/4”
P762 - 5/16”
P763 - 3/8”
P764 - 1/2”


Stainless Steel and Brass Nuts

Stainless Steel and Brass Nuts
Stainless SteelBrassJam Nut
S769 - #10
S770 - 1/4"
S771 - 5/16"
S772 - 3/8" S772JN - 3/8"
S773 - 1/2" S773JN - 1/2"
S774 - 5/8"C774 - 5/8"S774Jn - 5/8"
S774x34 - 3/4"


M-1 Structural Adhesive

M1 Structural Adhesive

P783 – M-1 Structural Adhesive/Sealant–10.1 oz tube.
Comes in grey, tan, black, white and limestone




-->